Mercury analyzer for water and aqueous solutions in Process applications

PA-2 / PA2-Gold

The mercury analyzer PA-2 is used for continuous monitoring of mercury concentrations in industrial processes.

The mercury process analyzer PA-2 is used for continuous monitoring of mercury concentrations in industrial processes. The system comes with either the VM-3000 or the UT-3000 photometer to meet different requirements regarding accuracy and sensitivity of measurements.

  • Fully automatic system
  • Easy menu-driven operation
  • Proven and reliable detection method: AAS
  • Measuring ranges from 10 ppt to 100 ppm
  • High flexibility of sample pretreatment
  • Suited for complex sample compositions
  • Low reagent consumption
  • Corrosion-protected construction
  • Automatic self diagnosis system for reliable operation
  • Quality control in chlorine-alkali plants
  • Monitoring of scrubber water of waste incinerators and power plants
  • Control of industrial sewage
  • Control of purification plants
  • Quality control of sulphuric acid
  • Quality control of drinking water
Technical Specifications
Measuring principle malgamation on MI GoldTrap (PA-2 Gold only), cold vapor atomic absorption (CVAAS) at 253.7 nm
UV-Source Electrodeless low pressure mercury lamp (EDL)
Stabilization method Reference beam method/td>
Optical cell Fused silica (Suprasil), lapprox. 230mm, heated approx. 55°
Measuring ranges PA-2 0,1 … 1 µg/l to 0…10 mg/l
Measuring ranges PA-2 Gold 0,01 … 1 μg/l to 0,1 … 10 μg/l
Sensitivity better than 0.01 µg/l
Response time approx. 1minute
Sample flow approx. 20 l/h
Carrier gas compressed air, filtered, approx. 30l/h, 1bar
Reduction reagent Tin-II-chloride or Soiumhydroborate
Reagent consumption apprx. 3l/week for each reagent
Sample digestion HCl or H2SO4, KMnO4 or H2O2 or Fenton’s Reagenz or NaClO3; depending on sample composition
Technical Data
Signal outputs analogue: 4 – 20 mA (500 Ω max.);
serial: RS232 / USB/td>
Status output Calibration; Autozero; Service; Malfunction; according to NAMUR 64 recommendations
Housing Fibreglass-reinforced polyester, for use in highly corrosive environment – Reagent storage cabinet made of chemically resistent plastic material/td>
Protection class IP 66 (EN 60529/ NEMA 3; 3R; 4; 4X; 12; 13)
Operating temperature 0 to 40°C
Sample temperature 65°C
Power supply 230 VAC / 50 Hz (110 VAC / 60 Hz option)
El. Power consumption 750 VA max. (PA-2 Gold, heating peak)
Dimensions (W x H x D) 62 x 78 x 33 cm
Weight approx. 50 kg
  • Our products are manufactured according to the ISO 9001 quality regulations.
  • CE approved

Related products

  • SolidFlow 2.0

    Continuous mass flow measurement of all types of dust, powder and granules in free fall and pneumatic conveying

    More
    10.00
  • Mercury Tracker-3000 XS

    Very small, ultra-light, with on-board GPS, data logger, battery pack and color TFT display for very comfortable and easy mercury monitoring in ambient air and other gases

    More
    10.00
  • LAS 300 XD

    In-situ & non-invasive measurement of NH3 & H2O, HCl & H2O, HF, low or high concentrations of CO and O2

    More
    10.00

Compare up to 4 products Show

Le nouveau site d’ENVEA est actuellement en cours de développement, fermez cette fenêtre pour poursuivre votre navigation. Vous pouvez aussi retrouver l’intégralité des rubriques en cliquant sur le bouton ci-dessous.

The new ENVEA website is currently under development, close this window to proceed your navigation. You can also find all the sections by clicking on the button below.
ENVEA
close-link
This site uses cookies. By the further use you hereby agree. For detailed information, please refer to the Cookies. Ok